Products

STICK (SMAW) Engine Driven Welders: LINCOLN S.A.E 400 Diesel welding Generator DC CC Perkins 1104C-4 4-cylinder liquid cooled Engine. Welding Range: 80-575Amps Auxiliary Power: 3000W, 60Hz, 110/20VAC O/P Socket.
MILLER Big Blue 500amps DC CC Duetz F3L2011 Air cooled Diesel Engine: Welding range: 65 -600Amps Auxiliary Power: 4000W Continuous.
MULTIOPERATOR & MULTIPROCESS Welder LINCOLN D.C 400 Ideal Arc DC welding Machine CC CV Multi Process DC Welder for SMAW, GMAW (MIG), FCAW and SAW Processes and Air Gouging Within the Capacity of the Equipment. Rated DC Output-- 400 Amps /36V/ 100% Duty Cycle. Input Voltage 415V/30.4 A -3 PH- 50/60 HZ Remote control capability allows operators fine tuning capability.
MILLER Gold Star 452 CC CV MULTI PROCESS DC WELDER STICK (SMAW), TIG (GTAW), AIR CARBON ARC (CAC-A FLUX CORED (FCAW) MIG SPRAY TRANSFER (GMAW) WELDING WITH VOLTAGE-SENSING FEEDER, 15 AMP 115 VAC DUPLEX RECEPTACLE allows operators the flexibility to run tools from power source without the need for additional 115 vac power in the weld area. Unique fan on-demand operates only when needed reducing noise, power consumption, and the amount of airborne contaminants pulled through the machine. rated output: 450 amp at 38 vdc, 60% duty cycle. Available in 4-pak, 6pak and 8pak Multi Operator Configuration.
MIG WELDER Deltaweld® 652 CC CV MIG (GMAW) ,Flux Cored (FCAW) ,Air Carbon Arc(CAC-A) Cutting and Gouging (3/8 in. carbons) Submerged Arc Welding (SAW) . Input Power: Requires 3-Phase Power. Rated Output:650A at 44 VDC, 100% Duty Cycle. Recommended Welding Range: CV mode: 15 - 44 V. Net Weight: 472 lb (214 kg). 15 amp 115 VAC duplex receptacle allows operators the flexibility to run grinders, drills, coolers, etc. from power source without the need for additional 115 VAC power in weld area.
ESAB MIG WELDER CC CV Welding Range: 75-630A, Maximum out put "100% duty cycle-500A, Mains Supply: 230/400/415/500-50. A power source for MIG/MAG, MMA welding and air-arc gouging a cost-effective combination. Sturdy galvanized metal casing with an air filter as an option made to withstand tough corrosive and dirty environments.
Wire Feeder DC CV CC SuitCase™ X-TREME™ 12VS MIG (GMAW), Flux Cored (FCAW) Gas and Self-Shielded Process use with CC/CV, DC Power Source. New! Polypropylene case with built-in slide rails and the ability to open the door to change wire with the feeder in a vertical position. Potted and trayed main printed circuit board for the harshest environments adds exceptional reliability. Improved contactor and overall duty cycle for high-amperage applications (425 A at 60%).
TIG WELDER LINCOLN PRECISION TIG 375 AC DC CC AC/DC (GTAW), STICK (SMAW), IDEAL FOR CRITICAL AC/ DC WELDING. TIG PRECISION -375 combines both outstanding value added features, with precision arc performance to meet all your welding needs. Range 2amps dc to 420amps ac-dc, duty cycle unbalance (70% penetration) 300amps @ 100 % duty -cycle, input power 380-415v, 3?- 50hz. 115vac 5amp weld switched cooler receptacle, ideal for critical AC/DC.
LINCOLN TIG MODULE AC DC CC AC/DC (GTAW), STICK (SMAW), Supplying high frequency for superior starting contactor control, remote control capability and a gas Valve for AC or DC TIG Welder (Polarity selection dependent on output characteristics of Power Source). Rated 300Amps/ 60% duty Cycle, Require 115V, Single Phase Input Power). Range 15 to 400Amp AC/ DC.
SUBMERGED ARC WELDER CC CV DC Multi Process DC Welder for STICK (SMAW), GMAW (MIG), FCAW, GTAW, Submerged Arc , Gouging, DC 600 features serious multi process welding with a full 600amp of welding Power, built in for high performance 24/ 7 Operation. Range: 600Amps @100% Duty Cycle. Input Current: 108/ 54A. LINCOLN LT-7 TRACTOR. LT-7 Tractor feeds 3/32 to 3/16" (2.4 to 4.8 mm) solid wires, from 100 - 400 inches per minute (2.5 - 10.2 m/min) wire feed speed. Calibrated tractor drive adjusts travel speeds from 6 to 70 inches per minute (0.12 to 1.8 m/min). Vertical head lift adjuster for adjusting electrical sickout from 1/2 in. to 5 in. (12.7 to 127.0 mm). Weld angle is up to 50° from vertical on either side; drag angle is up to 30° from vertical.
CUTTING EQUIPMENT SPECTRUM 1000 PLASMA CUTTER DC CC Rated at 1" (25mm) Cutting Capacity @ 10" / Min, and 3/8" @ 75" / Min. Starts without High-Frequency Cutting Capability Input Power208 - 575 V 1 or 3 Phase Required Input Pressure/Flow 7.8 SCFM (220 L/min.) at 90 PSI MIN (621 kPa) 120 PSI MAX (828 kPa) , Rated Output at 104° F (40°C)3-Phase 80 A at 150 VDC, 60% Duty Cycle (230-575 V), 50% Duty Cycle.
ROTATORS 15 ton to 100 ton Capacity rotators, Variable speed Motor, rubber wheels, Input 480 VOLTS, Remote hand Pendent Once the work-piece is supported onto rotators it can be rotated into precisely the required position for fitting, assembly and welding of the work-piece quickly, safely and efficiently. Rotators can be set up as fit up bed modules and can also be used to handle cylindrical structures while they are cleaned, painted.
POSITIONERS and MANIPULATORS Available in various Sizes and capacities. The use of a welding positioners enables the operator to manipulate his own work-piece un-assisted, provides accurate and consistent rotation speeds for high quality welds and optimum deposition rates, saves time wasted by cranes and reduces accident hazards and speeds up work and increases output through greater efficiency leading to a reduction in welding costs.

Air Compressors
185cfm to 900cfm portable Air Compressor, 100psi to 350psi (7 bar to 24 bar) Available with Zone-2 Safety features & Third Party Certificate.

Power Generator
5 KVA to 1000KVA, 380-415V, 50Hz Sound attenuated Generator. Available with Zone-2 Safety features & Third Party Certificate.

Lighting Tower
AMIDA LIGHTING TOWER 10KVA Diesel Driven Generator, 1000W x 4 Metal Halide Vapor lamps, 3KVA auxiliary 220V power. Available with Zone-2 Safety features & Third Party Certificate.

Winches
Electrical Winch 2 ton to 10 ton Capacity.

Excavator
Excavator with small and large bucket sizes. CAT 330 / CAT 235 KOM. Pc220 / Pc300 / Pc220 Also available Excavator with Jack hammer.

DOZER-R
CAT D8N /D8R KOM. D155A. D85LGP

WHEEL LOADER
CAT 966E / 966F CAT 950E / 950F KOM. WA 420

GRADER
CATERPILLAR 14G / 140H

VIBRATOR ROLLER
2 ton to 25 ton Vibrator Roller.

FORK LIFT
STILL- 1 ton to 5 ton capacity Battery operated STILL Fork lift Up to 6m lifting height. HYSTER- 2 ton to 15 ton capacity diesel engine operated Fork lift.

CRANE
20 TON TO 100 ton Truck Mounted, and Rough Terrain Crane.